U need
A compatible wireless adapter:
This is by far the biggest
requirement.The wireless card of
your computer has to be
compatible with the software
CommVIew. This ensures that the
monitor mode which is essential
for capturing packets.Click here
to check if your wireless card is
compatible
CommView for Wi-Fi :
This software will be used to
capture the packets from the
desired network adapter.Click
here and download the software
from the website.
After capturing the packets this
software does the actual
cracking.Click here-Click here and
download the software from the
website.
A little patience is vital!!
Download the zip file of
CommView for Wi-Fi from the
website. Extract the file and run
setup.exe to install CommView
for Wi-Fi. When CommView
opens for the first time it has a
driver installation guide. Follow
the prompts to install the driver
Run CommView for Wi-Fi.
Click the play icon on the top left
of the application window.
Start scanning for wireless
networks.
CommView now starts scanning
for wireless networks channel by
channel. After a few minutes you
will have a long list of wireless
networks with their security type
choose your target network
A few things to keep in mind
before choosing the target
wireless network
This tutorial is only for WEP
encrypted networks.
So make sure you select a
network with WEP next to its
name
Choose a network with the
highest signal.
Each network will have its details
in the right column.
are choosing has the least the
least dB (decibel) value.
Once you have chosen your
target network,select it and click
Capture to start capturing
packets from the desired
channel.
Now you might notice that
packets are being captured from
all the networks in the particular
channel. To capture packets only
from the desired network follow
the given steps.
Right click the desired network
and click on copy MAC Address.
Switch to the Rules tab on the
On the left hand side choose MAC
Addresses
Enable MAC Address rules
For 'Action' select 'capture' and
for 'Add record' select 'both'.
Now paste the mac address
copied earlier in the box below.
We need to capture only data
packets for cracking. Hence select
D on the bar at the top of the
window and deselect M
(Management packets) and C
(Control packets).
packets so that they can be
cracked later. To do this-
Go to the logging tab on top and
enable auto saving.
Set Maximum Directory Size to
2000
Set Average Log File Size to 20.
Now the boring part- WAITING!
NOTE: The amount of time taken
to capture enough data packets
depends on the signal and the
networks usage. The minimum
number of packets you should
capture should be 100,000 for a
decent signal.
packets (at least 100,000
packets)
Go to the log tab and click on
concatenate logs.
Select all the logs that have been
saved.
Do not close CommView for Wi-Fi
Now navigate to the folder
where the concatenated logs
have been saved
Open the log file
Select File- Export -Wire shark
tcpdump format and choose any
suitable destination.
This will save the logs with a .cap
Do Read : Best Android Hacks You Can Do Without Rooting Your Phone
Do Read : Best Android Hacks You Can Do Without Rooting Your Phone
extension to that location
Download Aircrack-ng and
extract the zip file.
Open the folder and navigate to
'bin'.
Run Aircrack-ng GUI
Choose WEP
Open your .cap file that you had
saved earlier.
Click Launch.
In the command prompt type in
the index number of your target
wireless network.
goes fine the wireless key will be
shown.
You may also receive a request to
try with more packets. In this
case wait until more packets
have been captured and repeat
the steps to be performed after
capturing packets
BEST OF LUCK
Do Read : Best Android Hacks You Can Do Without Rooting Your Phone
Do Read : Best Android Hacks You Can Do Without Rooting Your Phone
Do Read : Best Android Hacks You Can Do Without Rooting Your Phone
Do Read : Best Android Hacks You Can Do Without Rooting Your Phone
0 comments:
Post a Comment